| |
|
|
10 hp |
air compressor:
Quincy 350/20, 6 x 3-1/4 x 3-1/2 piston type, motor starter, Stoddard
silencer* (MN) |
|
10 hp |
air
compressor: Champion
HR10-8, two stage, four cylinder,
60 gallon tank, 220/3/60,
no motor starter* (MN) |
|
15 hp |
air compressor: Devair (DeVilbiss)
VAVC-5000
piston type, 52 cfm, 175 psi, sound
enclosure, no tank,
model 447 "V", four cylinder, 440/3/60,
1027 hours use, 2001* (MN) |
| 30"
x 48" |
autoclave: Anchor Autoclave AC sterilizer, 400F @ 50 psi (full vacuum @
300F), 7.5 KW heater, 1 hp vacuum pump, Reimers RH-20 20 KW steam generator,
hyd. single hinged door, locking ring, cart, Watlow temp & overtemp
controls, Partlow MRC7000 chart recorder, manual/automatic, never in
production, 300# load capacity,, 20" x 48" cart,, 1/4" shell, 5' x 9'
footprint, new 2002* |
|
3/4" |
auto
screw machine: Brown & Sharpe
#2, dynabrake, dual slide, bar feed, gears, 1964* (IL) |
|
24" |
back
gauge: rear operated, micrometer handwheel* (MN) |
|
42" x 22" |
baler: E.P. Baler, model P244, light duty,
42" x 22" x 32" bale, hydraulic,
32" x 54" x 105" high* (MN) |
|
18 gauge |
beader:
Pexto 0617-A, rotary
crimp & bead,
dies, hand crank operation,
extra dies, Feb-60* (MN) |
|
18 gauge |
beader:
Pexto 3617, rotary crimp & bead,
powered, extra rolls,
foot pedal, excellent, 1999* (MN) |
|
1-1/2" |
bender, power:
Diacro #8,
hydraulic, 1" solid, 1-1/2" tube (16 ga wall), 24" maximum radius,
3500# torque with 4" cylinder, 3 hp, 208-220/3/60, 1150#, Control-A-Bend, s/n - 1-1071* (MN) |
|
9" |
belt sander:
Engelberg vertical, tilt table, 3 hp, 220/440/3/60, $850.00* (MN) |
|
9" |
belt sander:
Porter Cable vertical, tilt table, 3 hp, 220/440/3/60, $850.00* (MN) |
|
bender, manual:
Diacro #3 rotary, dies* (MN) |
|
blast cabinet:
Vacu-Blast 200-P, 35"W x 21"H x 24"D, 20" x 21" part size, 1/2 hp blower,
1981* (MN) |
|
6-1/2" |
blasthole drill:
Ingersoll Rand DM45, Cummins
600 hp diesel (3000 hours on complete
rebuild), 5 rod
carousel (25' steels), crawler mounted (hard rock
carriage), hydraulic top hammer, rotary head (new gears 2006), 1200 cfm air compressor, hydraulic outriggers, extra 48" Dominator
hammers & extra long life 6-1/2" button type drill bits, sub
extender, 9130 hours, 13'1" W x 29'L x 15'6" H, 80,000#,
controls in cab, excellent
condition (7-8 on scale of 10),
under power, 1999* (US) |
| 1200#/hour |
blaster, dry ice:
Cold Jet D6520100M cryogenic blast system, (2) 600#/hour pelletizer barrels
make .140" (3.4 mm) soft pellets, 100- 350 psi air propellant operating
pressure, maximum CO2 temp of 0 degrees F, surge tank, heat exchanger, with
hoses, nozzles, etc., 460/3/60, 37 amp, new 1991, 30 hours use* (MN) |
|
350 MBH |
boiler:
Slant Fin "Galaxy",
model GG350HEC,
350,000 btu natural
gas, hot water to 240F, cast iron, (Caravan) for tandem use, natural
draft,
surge
tanks, 1999* (MN)(2) |
| 12
gauge |
brake, apron: Dreis & Krump, model SB612, 73" bending length, excellent
condition, 2275#, new 2001* (MN) |
| 8' x
3/16" |
brake, box & pan:
Dreis & Krump PBP-8187-8, mechanically powered, full set of fingers, dual
operator consoles, 1981* (MN) |
|
25 ton |
brake, press:
Diacro 16-72, hydra-mechanical, 6' x 16 ga, two speed, front operated back
gauge, 1970* (MN)(2) |
|
25 ton |
brake, press: Diacro
16-72, hydra-mechanical, 6' x 16 ga capacity, two speed, front operated back
gauge* (MN)(2) |
|
35 ton |
brake, press:
Diacro 14-72, hydra-mechanical, 6' x 14 ga capacity, two speed, front
operated back gauge, 1970* (MN) |
|
40 ton |
brake, press:
Pacific 40/8 hydraulic, 8' overall, 8' x 14 gauge capacity, 6-1/2' between
housings, die rail, dual footswitches, micrometer limit switches, 6' punch &
die, 230/460/3/60, wired 460 volt, 1970* (MN) |
|
90 ton |
brake, press:
Verson 206-65 mechanical, 8' overall, 6'6" between housings, 8' x 10 gauge,
die rail, Automec Autogauge CNC 1000 control, data plate, 24" back gauge,
440 volt, 1968* (MN) |
|
5 ton |
bridge crane:
underhung, Hoist Equipment,
30' span,
double
girder, 20' lift,
Detroit M10XL hoist, Smooth Move AC variable speed drives, pendant* (MN) |
|
5 ton |
bridge crane:
Dearborn, 37' span, single girder,
underhung, 20'
lift, Detroit
hoist, pendant, 1997* (MN) |
|
10 ton |
bridge crane:
Hoist
Equipment 36'6" span (wheel to wheel over runway), double girder,
top
running, pendant/radio,
Robbins &
Meyers hoist,
22'
lift, 37'5" span overall, 9'4" end truck width, 1989* (MN) |
|
10 ton |
bridge crane:
Hoist
Equipment 36'6" span, double girder,
top running,
pendant/radio, Robbins & Meyers hoist,
pendant, 22' lift, 11 fpm, 50 fpm speeds, 37''5" span overall, 1989*
(MN) |
|
10 ton |
bridge crane:
Orley Meyer-Shepard
Niles, 37'8" span (between crane rails), double girder,
top running, 10'3" wide end trucks + 7" of bumpers), low headroom hoist, 4' overall
height, 38'7" overall span, pendant/radio,
20' lift* (MN) |
| 10 ton |
bridge crane:
TM Equipment 36'6-1/2"" span, 8'4" wide, AC, double girder, top running,
15' lift, Shaw Box 72D10-015S13 hoist, 13 fpm, pendant/radio, 12,000#
overall weight, 1,800# for hoist, 37'2" overall span,
1996* (MN) |
|
10 ton |
bridge crane:
TM Equipment
37'5" span,
8'4" wide, AC,
double girder,
top running,
15' lift, Shaw Box 72D10-015S13 hoist, 13 fpm, pendant/radio, 12,500#
weight, 1800# for hoist,
38'1/2" overall span,
1997* (MN) |
|
15 ton |
bridge crane:
top running,
Dearborn,
36'1" span (between crane rails), AC,
top running,
double girder, pendant,
R&M Spacemaster
D8-15-31 (s/n - 158587VB1)
low headroom hoist,
10 hp, 3/4 hp trolley motor,
20' lift, 5'
overall height, 36'1" across end truck wheels, 36'11-1/2" overall span, 1988,
pendant, radio
control on crane, 208/230/460/3/60* (MN) |
|
15 ton |
bridge crane:
top running,
Shepard
Niles, 33' span (between crane rails),
top running,
double girder (11'1'" wide end truck + 4" of bumpers), 4' overall height,
34'1" overall span, low headroom hoist, 4' overall height,
hoist and hook,
pendant,
17'4"
lift, 16,280#, 40 fpm bridge & trolley, 14 fpm hoist, 1967. s/n - 67266*
(MN) |
|
15 ton |
bridge crane:
Zenar Milwaukee,
36' span, top running, double girder, class C, 20'2" lift, 10 fpm hoist, 50
fpm bridge & trolley, pendant. 11,800# bridge, 3800# for hoist/trolley, 7'2"
end truck wheelbase, 9'6" overall width, soft start, 460/3/60,
runway available, 1987*
(MN) |
|
15 ton |
bridge crane:
Zenar Milwaukee,
36' span, top running, double girder, class C, 20'2" lift, 10 fpm hoist, 50
fpm bridge & trolley, pendant. 11,800# bridge, 3800# for hoist/trolley,
10'1" overall end truck width, soft start, 460/3/60, runway available, 1989* (MN) |
|
15 ton |
bridge crane:
Zenar Milwaukee, 36' span, top running, double girder, class C, 20'2"' lift,
10 fpm hoist, 50 fpm bridge & trolley, pendant. 11,800# bridge, 3800# for
hoist/trolley, 7'2" end truck wheel base, 9'6" overall width, soft start,
460/3/60, runway available, 1987*
(MN) |
|
15 ton |
bridge crane:
Zenar Milwaukee,
36' span, top running, double girder, class C, 20'2" lift, 10 fpm hoist, 50
fpm bridge & trolley, pendant. 11,800# bridge, 3800# for hoist/trolley,
10'1" overall end truck width, soft start, 460/3/60,
runway available, 1989*
(MN) |
|
20 ton |
bridge crane:
Orley
Meyer-Shepard Niles, 36'6'" span, double girder (12'2" wide, 30" tall
I-beams), top running, 15'
lift, Shepard Niles
MDB hoist,
20 hp,
low headroom, 5' overall height, pendant, 12'
wide bridge, end trucks, 1970's* (MN) |
|
25 ton |
bridge crane:
top running,
Detroit Hoist,
36' span, AC
top running, double girder (33" tall x 12" flange),
15' lift,
new 1985,
9'8" wide end trucks (9' between wheels),
shortened
from 45'* (MN) |
|
220' |
bridge crane runway:
220' (x2)
of
18" tall I-beam,
7-3/4" wide flange,
12" wide
channel,
J-bolts, 30'
lengths of crane rail,
electrification, (20) 19'11-1/2' beams, (2) 21'11-3/8" beams with runway end
stops* (MN) |
|
250' |
bridge crane runway: 250' (x2) of 18" I-beam, channel iron, J-bolts,
top rail, electrification, under 10 ton crane* (MN) |
|
550' |
bridge crane runway:
top running,
W24x84 I-beams (18" I-beams sold), 9-1/4"
flange, 19'11-1/2" beams,
40' beams, 12"
& 15" channel cap, J-bolts,
4" crane rail, electrification,
for 20 ton cranes* (MN) |
|
720' |
bridge crane runway:
underhung, TC/American 3RH20-67,
20" tall x 1/2" web, 13" x 5/8" top
flange, 3-1/4" (hardened) bottom flange,
drilled & painted, 66.5#/foot, 47,880#, (24)
30'
I-beams, 360'
of double sided* (MN) |
|
2000#
|
bridge crane, stacker: Stanley
Vidmar Stak system, (80) 42" x 42" adjustable pallets, (4) 16' deep
x 4 bay sections, (2)
15' wide stacker cranes with forks,
12' lift, 1985*
(MN) |
|
5 hp |
buffer:
Hammond 18-A double end buffing/polishing lathe, 84" between tips, 1-1/4"
arbors, (2) 5 hp motors, independently variable speeds, hand brakes,
backstands with tension controls, guars, 230/3/60* (MN) |
|
5 hp |
buffer:
Hammond 5-VRROW-B double end buffing/polishing lathe, 96" between tips,
1-1/4" arbors, (2) 5 hp motors, 750 - 1500 rpm (independently variable),
hand brakes, backstands with tension controls, 230/60* (MN) |
|
7-1/2 hp |
buffer, double end:
Hammond 7VRO-D, 1000-2000
rpm (variable speed), 1-1/4" arbors, 48" between tips, 7-1/2 hp,
wheel guards, common
base, 460/3/60, Torit dust collector, s/n-14021, $5,000.00* (MN) |
| 500 pps |
camera, high speed: NAC
HSV-500 color VCR,
control pendant,
HSV-500
(model 120) high speed
video camera, 125, 250 & 500 pictures per second,
controls, f/1.6 aperture, 25 lux @ 250 fps (F4), 43 minute recording,
Panasonic TV,
Canon V6x10 18-100MM zoom lens,
Fujinon CL11052
close-up lens, cart, camera
powered up,
1997* (MN) |
| 48,000# |
chains: crane
sling, four 72" chains, 5/8" hook, no tags* (MN) |
|
5 ton |
chiller:
Liebert Challenger 3000,
65F-85F temperature, 20%-80% humidity, scroll compressor,
microprocessor control, audible/visual alarms,
1.5 hp evaporator fan, model BU102C-AA00,
air filtration,460/3/60, 2001* (MN) |
|
10 ton |
chiller:
Schreiber 1000AC, dual stage (2) 5 ton systems, 70 gallons/minute, 120,000
btu, 85 gallon (stainless) fluid reservoir, 3 hp compressor, digital
electronic control, low level warning, 1700# weight, 1999* (MN) |
|
90 ton |
chiller:
Advantage "Titan" TI-90W
43SRX central chiller, glycol
water cooled, semi
hermetic compressors (3 refrigerant zones), 101# R-22,
refrigerant gauges, 100 psi pressure
controls, 7.5
evaporator pumps,
25 hp pumps
(process & standy), 20F - 60F temperature,
460/3/60, 29 amp, mild steel
coolant reservoir, new
9/1997* (MN) |
|
320 ton |
chiller: Trane Earthwise CenTraVac, model CVHE450, water-cooled liquid
chiller, 700# HCFC-123 refrigerant, 180KW, 480/3/60, purge, three-stage
single compressor, condenser & economizer, 9416 hours compressor run time,
686 starts, Cutler-Hammer intelligent soft start, very clean, 450 ton
compressor, rated 300 ton with glycol, new 4/2003* (MN) |
| 1060 ton |
chiller: Trane Earthwise Centravac, model CVHF1060, water-cooled liquid
chiller, 2200# HCFC-123 refrigerant, 1000 ton @ 591 KW, 480/3/60, purge,
two-stage single compressor, condenser & economizer, 869 hours compressor
run time, 81 starts, Cutler Hammer intelligent soft start, very very clean,
new 4/2003, stretch wrapped* (MN) |
|
26" |
chip
wringer: Tolhurst,
2.85 cubic foot capacity, 250# capacity,
basket locking cover,
3 hp, new motor
starter & 110 volt transformer* (MN) |
|
18" |
cleaning, printed circuit board:
Speedline Accel
"Microline",
18" wide
conveyorized belt, precision (non-contact/inline)
for delicate semiconductor components/wafers, automated
in-line spray with
on-board water recycling,
wash/soak
control, under
belt wash, under
belt rinse, carbon & DI resin filter cartridges,
control, self contained,
1997* (MN) |
| 16"
x 24" |
cnc lathe: Wasino
LJ-6, 3500 rpm, 8.625" dia workpiece, 3.34" spindle bore, tailstock, chip
conveyor, 12 station turret, 12" 3-jaw hydraulic chuck, Fanuc O-T, 22 hp,
1990* (IL) |
|
2,000# |
coil
cradle/straightener: Littell 408-C-20, 8" x .187" straightener, 1959*
(MN) |
|
150# |
coil reel:
Rapid-Air R34AP,
4" stock width, 24" o.d.,
backplate, dancer arm, manual expansion, DC motor, payout/rewind,
120/1/60, 2000* |
|
250# |
coil
reel: Rapid Air RT-3
coil reel, single end, motorized, 7" width,
30" backplate, 1" & 1-1/2"
arbors, variable speed, hydraulic brake, reversing,
one with recoil spool* (MN)(2) |
|
500# |
coil
reel: PA Industries VR coil reel, single end, motorized, dancer arm/loop control, 4" width,
36" backplate, 198x* (MN) |
|
3,000# |
coil reel:
Bradbury 300SR, single end, plain, 24" width, manual expansion, drag brake,
1994 (OH) |
|
3,000# |
coil reel:
Bradbury 300DE, double end, plain, 24" width, 16"-20" i.d., 60" o.d.,
keepers, manual rotation & expansion, 1994* (MN) |
|
4,000# |
coil reel:
Littell 40-24, plain, 24" width, 60" o.d., manual expansion, electric brake,
1987* (MN) |
|
6,000# |
coil reel:
Littell 60-24, plain, 24" width, 60" o.d., 16" - 20" i.d., manual expansion,
electric brake, 1977* (MN) |
|
6,000# |
coil reel:
Littell 60-24, motorized, 24" width, 60" o.d., 16" - 20" i.d., manual exp,
electric brake, 1977* (MN) |
|
8,000# |
coil reel:
Cooper Weymouth Peterson 4RM24, motorized, 24" width, 60" o.d., 13" - 17"
i.d., manual expansion, sliding hold down arm, air brake, 1993* (MN) |
|
18" |
conveyor: EMI
5CLR-18, pedestal type, 4' length, adjustable height, 0 - 20 degree incline*
(MN) |
|
30 cubic ft |
corrosion test chamber:
Q-Fog CCT1100, 36" x
58" x 16" deep, moisture/salt spray/temperature
& prohesion, microprocessor for cyclic control (fog/dry-off/100%
humidity/dwell), 1100 liter, 120
liter solution reservoir,
all plastic construction, accepts (200) 4" x 12" samples,
1996* (MN) |
| 4 cu ft |
cryogenic deflasher: Cryogenic Systems LCC6000, belt style, freezes
parts to -205F with liquid nitrogen, 12" throwing wheel - shot
blasts/deflashes with plastic media, 3-5 minute cycle time, uses 1# of
nitrogen for 1# of parts, SOI control, media feed auger, MD100 7.5 KW dryer,
dust collector, 24" Sweco separator, vibratory unload tray, stainless
cabinet, 3" urethane insulation, low hrs, 1999 |
|
28" x 38" |
die cutter:
Standard Paper Box, "Econocut"
clamshell or clicker press,
open/closed/dwell timers (0-15 second), 15-25 strokes per
minute, fixed & rocking platens, Bijur lube, triple micrometer
impression adjustment, AB Micrologix 1000 PLC, color touch screen, electromagnetic clutch,
5 hp variable speed drive, 480/3/60,
7,200#, low hours,
double helical
gears, 2005*
(MN) |
|
28" x 38" |
die cutter:
Standard Paper Box,
"Econocut"
clamshell or clicker press, open/closed/dwell timers (0-15 second), 15-25 strokes per
minute,
fixed & rocking platens, Bijur lube, triple micrometer impression
adjustment, AB Micrologix 1000 PLC, color touch screen,
electromagnetic clutch, 5 hp variable speed drive, 480/3/60, 7,200#, low
hours,
double helical
gears, 2005* (MN) |
|
29" x 42" |
die cutter:
Standard Paper Box,
"Excalibur"
clamshell or clicker press, open/closed dwell timers, .937"
high cutting rule, chaseless dies, triple micrometer impression
adjustment,
color touch
screen, screens:
cycle,
indicator light,
main,
text message,
timer, AB Micrologix 1000 PLC, air clutch &
brake, 5 hp variable frequency drive,
motorized lube, 208/3/60,
7' x 7' x 5'H, (10,500#),
fixed & rocking platens,
helical gears (both like new,
factory rebuilt 2007* (MN) |
|
15 ton |
die
cutter: Preco 1212C, hydraulic press, C frame, 0"-4" stroke, micrometer
adjustment, 12" x 12" bolster, 230/3/60, Series 104 control, aftermarket
feeder, 2000* (MN) |
|
25 ton |
die cutter:
Herman Schwabe D, swing-arm clicker press, 3" stroke, palm buttons, 1980*
(MN) |
|
30 ton |
die cutter:
Samco GTH, model TH-35 2075,
travelling head,
joystick controller,
6" stroke, 1" - 7" daylight,
30" x 30" cutting
platen, 30" x
79" between uprights, 65" ram travel (left/right),
hydraulic, 3.2
hp motor (230/460/3/60),
64 litres Mobil DTE 26,
460/3/60, 2200 kg,
29-1/2" x 74" platens, 1996* (MN) |
|
40 ton |
die cutter:
Preco 1320-L, 4-post, hydraulic,
13" x 20" cutting area, 2" stroke,
micrometer adjustment, dual drive,
front & rear roll feeds,
SBCIII control, jog/speed/direction,
hydraulic,
light curtains, die
clamps,
electrical
cabinet,
21334 hours,
460/3/60,
1995* (MN)
|
|
die storage rack:
Better Concepts, (6) 36" x 36" roll out shelves, 2000# capacity/shelf* (MN) |
| 30" |
drill, gang:
Cleereman 4-spindle gang on 6-spindle base, 7-1/2 hp 30C heads, 50-1000 rpm,
power downfeeds, 24" x 156" T-slotted table, 1954* (IL) |
|
30" |
drill, radial:
Walker Turner, sliding overarm with tilt head, 26" x 18" table, 160-3800
rpm, 1/2 hp, 115/230/1/60* (MN) |
|
4' x 11" |
drill, radial:
Ikeda RM1300, 1440 rpm, 5 hp, #5 morse taper, 1966* (MN) |
|
5" x 13" |
drill, radial:
Ikeda RM-1575, #5
morse taper, 2-1/2" drill capacity, 30-1500 rpm,
power elevation & clamping, tapping,
coolant, box table,
13-5/8" column,
8800# weight, 89" x 36"
x 91"H,
7-1/2
hp, 230/460/3/60,
1991* (MN) |
| 16" |
drill, single
spindle: Electro Mechano 601J, bench base, 150-4000 rpm, ½ hp, #2 Morse
taper, 220/3/60, 1990* (MN) |
|
2200 cfm |
dust collector:
Rand-Bright 2200, wet
type scrubber, used on
flammable dust, 304 stainless
body, sound
silencer, water level
control, controls,
7-1/2 hp blower, 460/3/60,
s/n - 1322-2671*
(MN) |
|
1800 cfm |
dust collector:
Torit
SDF6 Downflo,
6 Ultraweb P191116-016-340
cartridges (103 sq ft), 618 sq ft filter area, pulse jet cleaning,
Checkerboard
control, 10 hp,
1997* (OR) |
| 4000 cfm |
dust collector:
Torit DFT2-8, DownFlo II, 8 cartridge, 2032 square foot filter area, 7-1/2
hp, reverse pulse jet, 1996* (MN) |
| 4160
cfm |
dust collector:
Dust Hog FJL-8-15-2H55, 8 cartridge, 2080 square foot filter area, 15 hp,
reverse pulse jet, 1995* (MN) |
| 5400 cfm |
dust collector:
Torit DFT3-12, 12 cartridge, pulse jet cleaning, 10 hp, breaker/reset/motor
starter, 6-pin control for constant cleaning, separate cyclone, extra duct,
2000* (MN) |
| 8000 cfm |
dust collector:
Torit DFT4-16, 16 cartridge, pulse jet, checkerboard control, 20 hp, 1998*
(MN)(2) |
| 17000 cfm |
dust
collector: Torit DFT3-36 Downflo II, 36 cartridge, reverse pulse jet
cleaning, Checkerboard control, Acme 429M A/9 blower, 50 hp (estimate),
supply duct, 1995* (OR) |
| 2.5 cu ft |
environmental
chamber: Blue M WSP-109C MP3, air to air thermal shock chamber, 85C to
200C hot, -75C to 200C cold, 14" x 14" x 19" stainless chambers, LN cooling,
Micristar controls, chart recorder, 1986* (MN) |
|
3 cu ft |
environmental
chamber: Standard Environmental Systems STB/2C, -100F to 350F, Watlow
920 control, RS232 port, cascading R502 & R-503 condensers with direct LN2
injection, O'Keefe 311B compressed air drier, Acme 3 KVA transformer
(240x480 primary, 120x240 secondary), 220/1/60, 1992* |
|
7 cu ft |
environmental
chamber: Thermotron F-7-CHII-5-5 chamber, fits MTS 55 kip load frame,
-100F to 300F temperature range, 15% - 95% humidity, 14" wide x 22" deep x
38" high chamber, 2 stage mechanical refrigeration with LN2 assist (21#
R502, 5# R13), heat/cool rate to 15F/minute, (2) 5 hp compressors with head
fans, 71 amp, 460/3/60, Thermotron 4800, controller, control features,
manual, 1983* (MN)(2) |
| 10
cu ft |
environmental
chamber: Tenney T10S, -40C to 200C temperature range, 24"W x 28"H x
27"D, 2000* (MN) |
|
10 cu ft |
environmental
chamber: Envirotronics TSV6-2-2-30 air-to-air vertical thermal shock
chamber, 24" x 30" x 25" deep basket elevates between -73C cold zone & 177C
hot zone, 30 KW heater, water cooled, (2) 30 hp compressors, R-404
(low) & R-508 (high) refrigerant, GN2 purge in cold zone reduces coil icing,
dual pen chart recorder, Systems Plus programmer/controller, RS232 port,
1.44 mb floppy, 200# part capacity, 460/3/60, 250 max circuit amps,
stainless interior, electrics & schematics, 2000* (MN) |
|
12 cu ft |
environmental chamber:
Ransco 16312, -73C to 177C temperature range,
cascading mechanical
refrigeration, air cooled,
27" x 27" x 27" chamber, R13 & R502 refrigerant,
Copelametic
1-1/2 hp compressors, 4 KW heater, 230/1/60,
LFE controller, two
shelves,
chart recorder, 1983* (MN) |
|
16 cu ft |
environmental chamber:
Envirotronics SH16C, -68C
to 177C temperature range, cascading refrigeration, (2) 1-1/2 hp
compressors, R-404A
, 20-95% humidity with Vaisala HMM30C solid state
sensor, 3 KW
boiler never used,
Systems Plus controller,
under power at -60C, 2 KW heater,
208 volt transformers, air cooled,
230/3/60,
1999* (MN) |
| 20
cu ft |
environmental
chamber: Test Equity 1020C, -75C to 175C temperature range, 40"W x 34"H
x 26"D chamber, R404A (non CFC) cascading refrigeration, Watlow F4 control,
chart recorder, 2000* (MN) |
|
23 cu ft |
environmental chamber: Thermotron F-32/23-HM-705-705 chamber,
fits MTS 110 kip load frame, -100F to 300F temperature range, 15% - 95%
humidity, 19" wide x 30" deep x 68" high chamber (extendible to 90" high),
32 cu ft extended, 2 stage mechanical refrigeration with LN2 assist (23#
R502, 10# R13), heat/cool rate up to 15F/minute, (2) 7-1/2 hp compressors,
head fans, 91 amp, 460/3/60, Thermotron 4800, controller, 7' x 9' x 11'
high, 1983* (MN)(2) |
|
27 cu ft |
environmental chamber: Blue M FRS-361G-1, 0F to 302F (-18C to 150C)
temperature range, 36" x 36" x 36" stainless chamber, window, 5% to 98%
humidity, Pro-Temp microprocessor controls, chart recorder, single
stage refrigeration, air cooled, 10# R-502, 2 hp compressor, water purifier,
7 KW heater, 1/2 hp blower motor, 480/3/60* (MN) |
|
27 cu ft |
environmental
chamber: Envirotronics SH-27, -22F to 350F temperature range, controls,
R-502 mechanical refrigeration, 20% - 95% humidity, 36" x 36" x 36" chamber,
window with wiper, air cooled, 1990* (MN) |
|
27 cu ft |
environmental chamber: Envirotronics SH-27, -68C/-90F to 177C/351F, R-22
& R-23, air cooled, cascade mechanical refrigeration, 36" x 36" x 36"
chamber, 20%-95% humidity, JC 600 two channel controller, chart recorder,
1/15 hp fans & wiring, Copeland KALB-0150-CAV-800 compressors, 230/3/60,
1993* (MN) |
|
27 cu ft |
environmental
chamber: Russells Technical Products RB-27-3, -20C to 177C temperature,
36" x 36" x 36" chamber, 22" x 22" window, water cooled, 3 hp
compressor, R502 refrigerant, 240/3/60, 12 KW heater, side ports,
chart recorder, Honeywell high & low limit controls, Watlow 920 control,
1995* (MN) |
| 30
cu ft |
environmental
chamber: Envirotronics EH30-2-3, -67C to 177C temperature range, 48" x
48" x 48" chamber, 20% - 95% humidity, air cooled, (2) 3 hp compressors*
(MN) |
|
31 cu ft |
environmental chamber:
Thermotron
F-31-CH-10-10-1,
-100F to 350F,
36"
x 36" x 40"H, double end, cascading refrigeration,
(2)
10 hp compressors (9#
R508B, 10# R404A), water cooled,
side
port, viewing window, Thermotron control,
floppy, 208/3/60, 109 amp load,
circulation fan),
7' LR x 5-1/2' FB x 8'4" H,
2002* (MN) (3) |
|
32 cu ft |
environmental chamber:
Tenney T32RC-2,
-73C (-99.4F) to
200C (392F), air cooled, cascading refrigeration,
(2) 2 hp
compressors (4.1#
R-404A &
R-23)2.5 KW heater, 20% - 98% humidity, 2 KW humidifier (1 gph),
dual pen chart
recorder, 230/1/60, window, glove ports,
Versa
Tenn V control,
36" x 40" x 38"
chamber with light,
communication ports, 50"W x 75"D x 86"H, 1600#,
2002*
(MN) |
| 32
cu ft |
environmental
chamber: Thermotron SM-32SL, -40C to 177C, R-502 refrigerant, water
cooled, Thermotron 2800 control, 1991* (MN) |
|
32 cu ft |
environmental chamber: Thermotron SM-32S, -20F to 350F temperature
range, 20% to 98% humidity, 38"x 38" x 38" chamber, Thermotron 2800 control,
alarm, one or two channel, R502 refrigerant, side port, air cooled, unused,
1992* (MN) |
| 36 cu ft |
environmental chamber: MVE
Hanse TC-9 (Chart REAL-36), -100C to 150C, LN2 cooling (vacuum jacketed
valve aseembly), 42"W x 38"D x 64"H, double-end/door,
side ports, 60C/min. change rate, high speed blower option moves twice
as much air, JC Systems 620A
FasTRAC control, windows, 480/3/60, 1999 (2) |
|
64 cu ft |
environmental chamber:
Despatch 16564,,,
48" x 48" x 48"
chamber, -35C to 177C temperature, mechanical refrigeration,
air cooled,
10% - 95% humidity,
Watlow F4
control, window,
chart
recorder, R502 refrigerant (9#), 208/3/60,
9 KW/3KW heaters,
10 amp, 65" W x 74" D x 96" H, 1991* (MN) |
|
64 cu ft |
environmental chamber:
Despatch EC2-64
Ecosphere, 48"
x 48" x 48" chamber, -29C to 177C, 4C to 85C with
humidity (10% - 98%), mechanical refrigeration,
air cooled, remote
condensor (compressor/receiver/condenser/controls),
suggest installing double size receiver for cold climates,
chamber base, Watlow 922
termperature control,
chart
recorder, window,
R404A refrigerant, 2001 certificate of calibration, 2003
calibration, 65" W x 74" D x 96" H,
dataplate, 1997* (MN) |
|
1-1/2" |
extruder:
Killion KN-150, 24:1 L/D ratio, 45#/hour, DC drive, 7 heat zones, 12" film
blowing die, rewind, 300 hours use, 1993* (MN) |
|
55 KIP |
fatigue tester: MTS 55 kip (312.31) frame, 55 kip load cell, Moog
72-102, 40 gpm valve, 162" tall frames fit 6.5 cu ft Thermotron chamber, 458
controller available (2) |
|
55 KIP |
fatigue tester: MTS 55 kip (312.41) frame, 55 kip load cell, dual 252
valves, missing service manifold, 189" tall frame fits 21 cu ft Thermotron
chamber, 458 controller available |
| 110
KIP |
fatigue tester: MTS 110 kip (312.41) frame, 110 kip load cell, missing
service manifold, 189" frame fits 23 cu ft Thermatron chamber, 458
controller available (2) |
| 30" x 120' |
filament winder:
EnTec 5K30-144, 4-axis, 2000# mandrel capacity, tracking creel with 12
rovings, Fibergraphix software, 1990* (MN) |
| 48" x
120" |
filament
winder:
EnTec 548-120-4, 4-axis,
4000# mandrel capacity, 0-133 rpm spindle speeds,
24 spool tracking creel, Fibergraphix, lengthened from 120" by EnTec,
26.5' overall, control,
1984* (CA) |
| 5 cu foot |
filter press:
Pacific Press P800E132A-15, 900 mm, (31) 31.5" x 31.5" gasketed
polypropylene plates, sidebar style press, center feed, four corner
discharge, plate shifter, air/hydraulic closure, 4 hoppers, 155" x 50" x 75"
high, 5567# weight, 42.3# plates, 1999* (MN) |
| 50 cu foot |
filter press:
JWI 1200G32-39/87-50/111SYLC plate & frame press, 1200 mm, (40) 48" x 48"
gasketed polyethlyene plates, 989 square foot filter area, double auger
conveyor, 2001* (MN) |
|
2500# |
forklift:
Hyster H25XM Cascade,
propane, 3-stage
mast, 153.5" lift height,
sideshift, 6 degree tilt, 42" forks,
Mazda
engine, solid tires,
650-10 front &
5.00-8 rear, 5700# weight, lab use,
only 142.3 hours on meter,
1995* (MN) |
|
2500# |
forklift:
Toyota FBE13 electric, triple stage mast, 3-wheel, 76" collapsed, 169"
raised, small foot print, 24 volt battery, charger, 36" forks, good battery,
s/n - FBE13-10231, 1979 |
|
2700# |
forklift: Clark TW40, 36 volt electric, newer Drexel battery, 171" lift,
sideshift, 36" forks, dataplate* (MN) |
|
3000# |
forklift: Clark C-500-30, propane, hard tires, 3-stage mast, 42" forks*
(MN) |
|
5000# |
forklift: Caterpillar M50LP, 36 volt electric, 42" forks, two stage
mast, 130" lift height, non marking tires* (MN) |
|
6,000# |
forklift:
White MA60, propane, hard tire, 2 stage mast, 42" forks, 1968* (MN) |
|
2000 F |
furnace, box: Lindbergh 52561-AP1-H200, 1100C, 20 KW electric, 230/3/60,
70 amp, 24"W x 18"H x 36"D, mold-a-therm encapsulated electric heating
elements, Honeywell DCT-216 temperature & overtemperature controllers,
single door, test run & ready to ship, 1993* (MN) |
| 2000 F |
furnace, box:
Lindbergh 52661-P-B, 1100C, 26 KW electric, 240/3/60, 70 amp,
26"W x 25"H x 36"D, mold-a-therm encapsulated
electric heating elements, Honeywell DCT-216 temp & overtemp controllers, single door,
1994* (MN) |
|
1850F |
furnace, carburizing: Leeds & Northrup Vapocarb, 7.2 KW 1850F & 3.7KW
1750F furnaces, controls* (MN) |
|
1250 F |
furnace, fluidized bed:
Procedyne
HT-1250-2032, 20"
diameter x 32" deep pit (retort), aluminum oxide (120 mesh) bed
material, fluidized gas (compressed air or nitrogen), 30 KW, 60 amp,
460/3/60, Honeywell UDC3000
controls, chart recorder, GP-11
humidifier, methane, nitrogen,
electrical box, more
controls, bed
temp controller, uses
inert gases, for tempering, marquenching & stress relieving,
manuals, vertical lift cover on
swing arm, 11/1982* (MN) |
|
2050 F |
furnace, fluidized bed:
Procedyne QB2032 (quench
bath), model HT-2050A-1424,
14" diameter
x 24" deep pit (retort), fluidized gas (compressed air or
nitrogen),
powered
cover, 48 KW, 55 amp, 460/3/60, gas
gauges,
ammonia, methane,
Honeywell
DCP700 controls, chart recorder,
excellent condition, control,
atmosphere as currently
stored, cycle
timer, vertical
lift cover, vary cfm of fluidized gas and air in retort
to control temperature, 11/1982* (MN) |
|
750 F |
furnace, salt bath: Ajax IQC-3020, 10 KW, 18" x 22" opening, 450F -
750F, uses Nitrate salt, with 1/4 hp Lightnin mixer, quench for parts coming
out of furnace, electrodes (immersion heaters), 10 KW, 440 volt, 1958* (MN) |
|
5 hp |
granulator,
plastic: Nelmor G810P1, 8" x 10" feed throat, 3 rotary knives, 2 bed
knives, 1995* (MN) |
|
7-1/2 hp |
granulator,
plastic: Polymer 912-SP,
9" x 12" feed throat,
2 rotary knives,
2 bed knives, 230/460/3/60
electrics, s/n -
74277* (MN) |
|
3.5" |
grinder,
centerless: Cincinnati #2EA, 8" wheels, hydraulic grinding wheel
dresser, through feed rest, 1942* (MN) |
|
5" x 12" |
grinder, cylindrical: Myford MG12, hand feed, 10" grinding wheel, 2 hp
wheel head, 100-900 rpm, 3/4" maximum collet size, tailstock, 1974* (MN) |
| 10" x 18" |
grinder,
cylindrical: Jones & Lamson Format 15/450, Allen Bradley 8600 cnc
control, 18" grinding wheel, 5 hp motor, inch/metric, 1.5 hp workhead,
excellent, 1995* (IL) |
|
10" x 20" |
grinder, cylindrical:
Brown & Sharpe #1 universal, swing-down internal attachment, magnetic &
3-jaw chucks, temporary specs, 1959* (MN) |
| 10" x
20" |
grinder,
cylindrical: Landis 1R universal, motorized workhead, lots of tooling,
1972, POR* (IL) |
|
3.125" |
grinder, drill:
Brierley ZB80, semi-automatic, .197" - 3.125" capacity, 40-180 degree point
angles, 2-3-4 flutes, powered work-head and cross-slide, point splitting
attachment, coolant, 1990* (MN) |
| 31.5" x
157" |
grinder, roll:
Waldrich Siegen
Ingersoll WSIIIa80/6, camber
- convex/concave,
gears, 50" actual swing, 164" centers, 12,000# roll weight w/o supports, 9 - 72 rpm faceplate, 27.5" x 2.75" grinding
wheel,
3 work rests, 3 (Yaskawa
GPD 515/G5,
Yaskawa GPD 515/G5,
Magnetech GPD 515) variable frequency drives & motors added in 2005, rescraped ways in 1997, 28' x 10' x 7'
H + motor, 19' x 2' x 6-1/2' electrical control box,
Encyclon filter,
controls, 1964* (MN) |
|
20" |
grinder, snag:
U.S. Electrical Tool 62VSA, double end, variable speed, dual 7-1/2 hp
motors, 208/230/460/3/60, 1750 rpm, adjustable rests, 20" x 2" x 10"
wheels, grinding wheels (Radiac Abrasives C202P 2340 rpm),
460/3/60* (MN)(3) |
|
6" x 18" |
surface:
Harig 618 "Carbide Hogger", manual/hydraulic, 1/1 hp, 560/3500 rpm spindle,
fine feeds (vertical & cross), 6" x 12" magnetic chuck, 1978* (MN) |
|
6" x 18" |
surface:
Harig Super 618 manual, 6" x 18" chuck, coolant, 1975* (MN) |
|
6" x 18" |
grinder,
surface: K.O. Lee S718, manual, coolant, 6" x 18" magnetic chuck, 1976*
(MN) |
|
8" x 24" |
grinder,
surface: DoAll
D824-12, hydraulic, 12"
grinding wheel, 8" x 24" chuck,
power
downfeed, 5 hp grinding spindle motor,
coolant, cleaned
& painted,
controls,
80" x 60" x 75" high, 1980* (MN) |
|
2 ton |
hoist, cable: R&M DB-2-24 electric, plain trolley, 2 hp hoist motor,
460/3/60, before removal, 20' & 23' wall mounted jib arms, 460/3/60*
(MN)(5)* |
|
2 ton |
hoist, chain:
Coffing ECMT-4024, powered trolley, 15' lift, pendant & radio control*
(MN)(3) |
|
2 ton |
hoist, chain:
Wright-Way electric cable, product 2215041, 20' lift, power trolley, 8 fpm
lift speed, pendant, 230/460/3/60, unused in original box, 1993* (MN) |
|
5 ton |
hoist, chain:
Detroit M10XL electric cable, underslung power trolley for double girder
bridge, magnetic brake, 20' lift, 2 speed, very slight use, 1985, 2,650.00*
(MN) |
|
3.75" |
hone: Sunnen
MBB-1690, power stroker (80-310 spm), .062"-3.75" diameter, 200-2500 rpm,
1/2 hp, some tooling, 1978* (MN) |
|
3.75" |
hone, horizontal:
Sunnen MBB-1800, "power
stroker", .060" - 3.75" capacity, 20 - 2500 rpm spindle speeds,
80/110/160/220/310 spm stroking rates, 1 hp spindle motor, 1/2 hp stroke
motor, cabinet
full of tooling,
s/n - 73164* (MN) |
|
10" x 12" |
hot plate welder:
Branson
HV12, 12" x 15"
aluminum heat platen,
10" X 12" part size, pnuematic operation, 10" between
(14" x 17") press platens, 10" press platen
stroke (each), 14" in/out heat platen stroke, 4" left/right heat
platen stroke, Allen Bradley SLC500 PLC, Total Control Quickpanel Jr
touch screen, 480/3/60,
enclosure, 66" x 52" x 79" overall dimensions,
1800#
weight, 2001* (MN) |
|
10" x
12" |
hot plate welder:
Branson
HV12, 12" x 15"
aluminum heat platen, 10" X 12" part size,
pnuematic operation, 10" between
(14" x 17") press platens, 10" press platen
stroke (each), 14" in/out heat platen stroke, 4" left/right heat
platen stroke,
Allen Bradley SLC500 PLC, Total Control Quickpanel Jr touch screen,
480/3/60,
enclosure, 66" x 52" x 79" overall dimensions,
1800#
weight, 2001* (MN) |
|
10" x 12" |
hot plate welder:
Branson
HV12, 12" x
15" aluminum
heat platen, 10" X 12" part size,
pnuematic operation, 10" between
(14" x 17") press platens, 10" press platen
stroke (each), 14" in/out heat platen stroke,
4" left/right heat
platen stroke,
Allen Bradley SLC500 PLC, Total Control Quickpanel Jr touch screen,
480/3/60, 66" x 52" x 79" overall dimensions,
1800#
weight, 2001* (MN) |
|
10"
x 12" |
hot plate welder:
Branson
HV12, 12" x 15"
aluminum heat platen,
10" X 12" part size, 10" between platens, 10" press platen
stroke (each),
14" in/out heat platen stroke,
4" left/right heat
platen stroke, Allen Bradley
SLC500 PLC, Total Control Quickpanel Jr touch screen:
startup
screen,
weld setpoints/last weld
screen,
tooling screen,
ready to cycle screen,
480/3/60,
plexiglass enclosure, 66" x 52" x 79"
dimensions,
pnuematics, 1800#
weight,
2001* (MN) |
|
6 ton |
insertion machine: Haeger HP6-C-2, hydraulic, 18" throat, foot pedal,
AF-MAS automatic bowl feeder with vacuum generator & counter, work light,
foot controls, 1985* (MN)(2) |
|
6 ton |
insertion machine:
Haeger 618, hydraulic, 18" throat, 0"-8" stroke, 1200 insertions/hour, 1999
& 2001* (MN)(2) |
|
28" |
lapper: Engis
Hyprez 28LM460VP production lapper, 0-100 rpm, (3) conditioning rings,
diamond compound dispenser, 3 hp, 1991* (MN) |
|
28" |
lapper: Engis Hyprez 28LM460VP, 0-100 rpm (variable), (3) 12"/13.87"
conditioning rings, independent pressure regulators, 35" work height,
MiniMizer lapping dispenser, pump, auto lubrication, 3 hp, 460/3/60, 1993*
(MN) |
|
48" |
lapper:
Peter Wolters AC-1200, double
sided,
swing away upper wheel, 2-5/8" thick cast iron lap plates, 7.5 kw
drives, (5) 18.62"
pin driven carriers (carriers unavailable),
outer pin ring,
automatic
sizing, swing away dresser,
Siemens
S5 PLC, polishing
software,
control
pendant,
BGK chiller,
10,764 hours use,
480/3/60, 52.3 amps, 6800 kg weight, used 1-1/2
years to polish (fine grind) silicon wafers (aluminum/titanium) with
gum rubber diamond slurry,
1993*(MN) |
| 11" x 18" |
lathe, precision:
Hardinge HLV-H, 125 - 3000 rpm, threading,
Sony 2-axis DRO,
3-jaw &
4-jaw
chucks, 5C collets,
power carriage feed,
tooling, Aloris tool post,
1.5 hp, 230/460/3/60,
coolant, very tight,
HLV-H-6121M* (MN) |
|
10" x 20" |
lathe, engine:
Monarch
EE precision
toolmakers lathe,
inch/metric threading,
taper attachment (ball bearing),
13-1/2" actual swing, 40-4000 rpm spindle
speeds, tube type
drive,
extra tube, 5
hp motor, 1-3/8" spindle hole, D-1 camlock spindle nose, (2) 4-jaw
chucks, faceplate, 3-jaw chuck, steady rest,
worklight,
inch/metric
handwheels, headstock
feed gears, chip
guard, 460/3/60,
3450# weight, 1982* (MN) |
| 12"
x 36" |
lathe, engine: Clausing 5916,
52-2000 rpm (variable speed), belt drive,
taper attachment, collet closer,
toolpost, 6-jaw chuck (no jaws), faceplate, turret stop, worklight, s/n - 508610* (MN) |
| 14"
x 48" |
lathe, engine: South Bend model CL185D, belt drive, 3 jaw chuck* |
| 15" x 54" |
lathe, engine:
LeBlond Regal, 30-1200 rpm, servo shift, inch/metric, taper, chucks, 1981*
(MN) |
| 16" x
78" |
lathe, engine:
Monarch, Series 60, 18-1/2" actual swing, geared head, 800 rpm, taper
attachment, Accurite III 2-axis digital readout, government stored,
excellent, steady rest, Cushman 12" 3-jaw chuck, 1954* (MN) |
|
20" x 80" |
lathe, engine: DoAll Romi 20H, 4-1/8" hole,
45-1700 rpm,
inch/metric, hard ways,
taper, steady,
excellent, light use, tight screws, quiet head, 15 hp, 1987* |
| 24"x135" |
lathe, engine:
Dainichi DH-135, 35" swing in gap, 16-1200 rpm, , inch/metric threading,
3-jaw & 4-jaw chucks, 2-1/4" spindle hole, coolant & chip pans, 1967 (MN) |
|
26" x 144" |
lathe, engine:
LeBlond
Makino Regal Servoshift, 20-1600 rpm, inch/metric threading, 3"
spindle hole, no taper, 3-jaw chuck, L2 spindle nose, toolpost, worklight, coolant &
removable chip pans, 30/15 hp motor, 460/3/60, 200" overall
length,
9200#, 1984* (IL) |
| 36.5" x
240" |
lathe, engine:
LeBlond 3220-25 Heavy Duty, (36) speeds, 10 - 1300 rpm (lever shift), 25"
swing over cross slide, carriage rapid traverse, taper attachment, 3-jaw &
4-jaw chucks, steady rest, chip pans, coolant, 40 hp spindle motor,
208/416/3/60, 2700 hrs use in maintenance facility, tailstock, 1971* (IL) |
|
9" x 18" |
lathe, second
operation: Hardinge DV-59 second operation, lever cross-slide, lever
turret, 1961* (IL) |
| 17" x 55" |
lathe, wood: Oliver 2255, (16) spindle speeds, 90-2600 rpm, 2 hp Lima
drive, 230/460/3/60* (MN) |
| 6 ton |
marking: Schmidt
#175-6 hydraulic, 7" roll travel, 25" die space, 12" riser, 18" between
housings, 3 hp, 220/440/3/60, rotary fixture, palm buttons, 1956*
(MN) |
|
40-2000X |
microscope:
Zeiss Axioskop 50,
10X & 20X eyepiece
magnification,
4X, 10X,
40X & 100X
objectives, stereo/binocular,
light source,
Bausch
& Lomb camera (3X,
5X, 7.5X 10X), s/n - 451485,
base, extra
base* (MN) |
|
microscope,
toolmakers: Optometrics, micrometer adjustable stage, vertical
adjustment, illumination, (4) with 2-axis digital readout, (1) without
readout* (MN) |
|
12" x 53" |
mill,
horizontal: Cincinnati
207MK, telescoping quill,
rear controls, 7-1/2
hp, 1976* (MN) |
|
141 cu in |
mill, laboratory: Thomas-Wiley model 4, 7-3/4" diameter milling chamber,
2-1/4" diameter sample input, 50 to 1000 grain sample volume, 800 rpm @ 60
Hz or 667 rpm @ 50 Hz, 4 adjustable rotary knives, 6 adjustable bed
knives, hinged steel door* (MN) |
|
4" x 12" |
mill,
production: Barker PM hand,
5" x 3" x 3" travels, 1/2" through collet tube,
1/3 hp, 115/1/60, 19xx* (MN) |
| 8"x6"x7" |
mill, vertical:
DynaMyte 2800 bench mill, 3-axis cnc, Dyna 2800 control, 8000 rpm, 16" x 6"
table, 200# capacity, toolholders, RS232 port, one shot lube* (MN) |
| 9" x 36" |
mill, vertical: Bridgeport
Series I, vertical, 1-1/2 hp (needs bearings),
60-4200 rpm, Accurite II dro (missing scale) , x & z
power feeds, power draw bar,
ways, newer head,
1971* (MN) |
|
9" x 42" |
mill, vertical: Bridgeport, 1-1/2 hp variable speed, 6" vise, 1972* |
|
9" x 42" |
mill, vertical:
Bridgeport, 1-1/2 hp
variable speed head, x & y digital readout scales (no readout),
power feed (missing pf
controller), 1974* (MN) |
| 9"
x 42" |
mill, vertical:
Bridgeport, 1-1/2 hp variable speed head, x & y
ballscrews
(cnc reconversion), R8
spindle nose, 480/3/60, with Everede heady,
1974* (MN) |
|
9" x 42" |
mill,
vertical: Bridgeport Series I, vertical, 1-1/2 hp, 60-4200 rpm, Accurite III
dro w/one scale, x & z power feeds, chrome ways, power draw bar, 1979* (MN) |
| 9"
x 42" |
mill, vertical:
Bridgeport Series I, 2 hp, variable speed, power feed, 2-axis dro, 1987*
(MN) |
|
9" x 42" |
mill, vertical: Bridgeport Series I, 2 hp, 60-4200 rpm, chrome ways,
Accurite III 2-axis dro, power feed, Kurt power draw bar, worklight, one
shot lube, 1988* (MN) |
|
9" x 42" |
mill, vertical:
Bridgeport Series I,
2 hp variable speed
head, power feed,
Quality
500 2-axis digital readout,
Quality 500 scales, painted, new R8 spindle with bearings,
1992* (MN) |
|
9" x 42" |
mill, vertical:
Bridgeport Series I,
2 hp variable speed,
chrome ways, power feed, Futuba
Pulscale 2-axis digital readout, 200-480/3/60,
R8 spindle nose, 480/4/60,
1994* (MN) |
|
9" x 48" |
mill, vertical: Bridgeport EZ-Trak Plus CNC, vertical, 2 hp, 60-4200
rpm, new spindle bearings, Bijur auto lube, Kurt power draw bar, worklight,
chrome ways, one shot lube, EZ Trak control, vise, 1992* (MN) |
|
11" x 58" |
mill, vertical: Bridgeport Series II, vertical, 4 hp, 50-3500 rpm, 30"
x, 15" x & 16" z travels, 3-axis power feeds, chrome ways, Accurite 3-axis
3X/D200 digital readout, #40 spindle taper, Bijur one shot lube, Bijur ULA
spraymist coolant, pump & reservoir, tool holders, 230/460/3/60, tight machine (.017" play on x, .005" play on y & z), 1990*
(MN) |
|
3/16" |
nibbler:
Trumpf CN-500 copy nibbler, 54" throat, sliding x-rail with clamps, tooling,
550/3/60, more tooling, 20 mm x 24 mm tool shank, 198x* |
|
1/4" |
notcher:
Profab (Roper Whitney),
corner radius machine,
model 900, 13" serrated blade with 11 radiuses,
electrics, 1984* (MN) |
|
350F |
oven, batch:
Precision Quincy 40A-350,
electric, 36" x 36"
x 36", double doors,
recirculation,
purge, forced exhaust,
control,
208/3/60, 73.9 amp,
48" x 57" x 84" high (shipping),
1985* (MN) |
|
400 F |
oven, batch:
Thermatronix 96" x 36" x
48" deep, 36 kw electric, recirculation, dial temp control, 122,800
btu, 50 amp, 460/3/60, with
fixture to rotate filament windings* (MN) |
|
400 F |
oven, batch: Despatch V-35, 16 KW electric, 48"W x 30"D x 42"H, 3
shelves, recirculation, digital temperature control, 6-1/2' x 3' x 7' high
overall, 480/3/60, 19.3 amp* (MN) |
|
500 F |
oven, batch:
Despatch V-29, 12
KW electric, 37"W x 25"D x 37"H, aluminum interior,
3 shelves, double
door, recirculation,
timer, Partlow
temperature control & high limit,
480/3/60* (MN)
|
|
500 F |
oven, batch:
Despatch V-35, 16 KW
electric, 48"W x 30"D x
42"H, 3 shelves, recirculation,
windows, LFE digitial temperature
control, 6-1/2' x 3' x 7' high overall,
208/3/60, 44.5
amp* (MN) |
|
500F |
oven, batch:
Despatch V-35, 16 KW
electric, 48"W x 30"D x 42"H, recirculation, Partlow control, 550/3/60,
16.8 amp, 84" x 40" x 76" high (shipping)* (MN) |
|
600 F |
oven, batch: Blue M POM-246G, 316C/600F operating temperature, 36" W x
24" D x 48" H, single door, 8 shelves, 316C/600F operating temperature, 11
KW electric, 316 C, 440/3/60, 1 hp recirculation, Omega digital temp
indicator, Partlow temperature control, Blue M memory ring control, pricing*
(MN) |
|
600F |
oven, batch:
Blue M POM-246FX, 36"W
x 24"D x 48"H, electric, 240/3/60,
Power-O-Matic
temperature &
overtemperature controls,
forced exhaust, shelf
brackets, 60" x 50" x 92" high (shipping)* (MN) |
|
650 F |
oven, batch:
Blue M POM-1406B-1, electric, 48"W x 36"H x 24"D, double doors,
recirculation, 460/3/60, 46 amp, polished aluminum interior, controls* (MN) |
|
650 F |
oven, batch:
Blue M POM-1506G-1XX, electric, 36"W x 30"H x 24"D, double doors with
windows, 3/4 hp recirculation, polished aluminum interior, controls,
480/3/60* (MN) |
|
662 F |
oven, batch:
Blue M STL-05-C-MP350
stacked oven, double door, electric, 25" x 20" x 20" high, 5.8 cubic foot
(each), stainless interior, horizontal airflow, chart recorders & controls,
240/1/60, 6 KW* (MN) |
|
850F |
oven, batch:
Despatch CF-32, gas fired,
37"W x 25"D x 37"H,
double doors, shelves, recirculation,
dataplate, 220/3/60
electrics,
Eclipse burner valve,
extra
valve picture, 96" x 40" x 69" high, 80" with exhaust* (MN) |
|
850 F |
oven, batch:
Despatch V-35SD, electric, 42 KW, 48"W x 42"H x 30"D, aluminum interior,
double doors, forced exhaust, recirculation, 6 shelves, 240/3/60* (MN) |
|
850 F |
oven, batch:
Grieve HC-850G, gas fired, 50" x 50" x 50" interior, forced exhaust,
recirculation, double door, controls, chart recorder, 1964* (MN) |
|
800 F |
oven, burn-off:
Controlled Pyrolysis PTR-260, 60"W x 72"D x 72"H, 350,000 btu primary gas
burner, Pollution control secondary burners to 1400F, water spray system,
Honeywell controls, floor/cart, 1991* (MN) |
|
400F |
oven, infrared:
BGK "flatline" curing system,
24" wide metal mesh
conveyor, 17' oven length, six
heat zones (sides & top),
1-1/2 hp blowers,
1/15 hp forced
exhausters, 81.1
KW, 107 amp, 480/3/60,
controls, 400F @ 3.5'/minute speed,
product detect photo eye (idles heaters when belt empty), 3' heat section,
6' cool down, 3' entry, 3' exit, 2' transitions,
excellent, 175" x 44" x 84" high, 1997* (MN)
|
| |
oven, reflow:
BTU Paragon 150, right to left, 10 upper & 10 lower heat zones, edge chain
conveyor, mesh belt, fixed rail on front, 1997* (PA) |
|
300 F |
oven, vacuum:
T-M Vacuum Products PC36-6, 36" x 36" x 36" chamber, 27 cubic foot, 10-20
micron vacuum, stirring fan, automatic w/gas backfill, sight glass, digital
controllers, 1997* (MN) |
|
350 F |
oven, vacuum:
T-M Vacuum
Products PC-36-2,
27 cu foot,
36" x 36"
x 36" chamber,
Alcatel 2033 rotary vane vacuum pump, 27.5 cfm, produces 1 torr
(10 - 20 micron) vacuum, Copeland
air cooled compressor,
917
Pirani & 0-30 Hg vacuum gauges,
automatic
gas w/backfill,
missing
stirring fan,
electrical cabinet, viewing window, electrical cabinet,
temperature
controls, silicon heat elements, 460/3/60,
1996*
(MN) |
|
450 F |
oven, walk-in: Precision Quincy EC-506-6, 60"W x 72"H x 72"D, 350,000
btu, gas fired, single end, excellent, 1986* (MN) |
|
500 F |
oven, walk-in: Grieve TBH-500, 24 KW electric, 48"W x 48"D x 64"H,
double doors, new heating elements, floor, controls, 6' x 6' x 6' overall*
(MN) |
|
500F |
oven, walk-in: Despatch PSC3-26R-G, propane, 54"W x 76"H x 8'10"D,
single end, double door, floor, rear mounted heater box, digital temperature
& overtemp controls, recirculation, 208/240/480/3/60, 5 hp
forced exhaust, 1994 |
|
500 F |
oven, walk-in: Despatch PWC3-14-1-G, double end, gas (burners) fired,
54"W x 68"D x 66"H, double door, floor, controls, 4" wall insulation,
top mounted heater box, 1985* (MN) |
|
500 F |
oven, walk-in: Grieve TBH-500, gas (burners) fired, 36"W x 48"D x 60"H,
floor w/cart tracks, forced exhaust, recirculation, purge, control* (MN) |
|
550 F |
oven, walk-in: Despatch S-250, gas fired, 84" x 84" x 150"D, single end,
top mounted heater box, Partlow temperature control, forced exhaust, 3 hp
recirculation fan, 220/3/60, DG350 350,000 btu burner, update 1994,
currently dismantled and palletized for shipping, 1962* (MN) |
|
650F |
oven, walk-in:
Despatch RS-4-HD, gas
fired, 56"W x 72"D x 72"H,
single end, double doors, digital temperature
control, chart recorder, 96" x 83" x 89" H, 65" x 48" x 52"
high rear
mounted heater box, 74" x 36" x 18" control stand* (MN) |
|
650 F |
oven, walk-in: Precision Quincy 102-650T, 250 KW electric, 6' LR x 10'
FB x 6' H, single end, double doors, recirculation, forced exhaust, digital
controls, chart recorder, vertical/horizontal airflow, 58" height above 5'6"
x 9'6" powered cart, floor, 8'6" LR x 11' FB x 12' H overall, top mounted
heater box, 340 amp, 1990* |
|
packaging: Accucount 10, controls, 117/1/60, (2)* (MN) |
|
packaging: Accucount 15 parts counter, controls, extra picture, extra
picture* (MN) |
| |
pad printer:
Tampo Print Hermetic 90, 10 mm x 80 mm stamp, rotary table, 1999* (MN) |
|
100 cfm |
plastic, drier:
Dri-Air ARID-X dessicant drier, dual hopper, quick changeover, digital
controls, 1995 (MN) |
|
27 mm |
plastic, extruder: Leistritz MIC27/GL-320 twin screw laboratory
extruder, maximum 500 rpm, 12 KW drive, extra screws, 53 hours use, 1995*
(MN) |
|
1-1/2" |
plastic, extruder:
Killion KN-150, 24:1 L/D ratio, 45#/hour, DC drive, 7 heat zones, 12" film
blowing die, rewind, 300 hours use, 1993* (MN) |
|
7-1/2 hp |
plastic,
granulator: Nelmor G1012P1, 10" x 12" cutting chamber, 3 rotary knives,
2 bed knives, top loading, 230/460/3/60, currently wired 460 volt, 1995*
(MN) |
|
10 ton |
plastic, injection molder: Autojectors VS10-S, 10 Series insert molder,
.98 ounce, 3/4" vertical screw injection (7" stroke) & clamping (7" stroke),
20:1 L/D, C frame, 8" x 14.5" upper platen, 6" x 8" lower platen, 6" x 39"
shuttle table, 16" shuttle table stroke, INX6000 Total Touch control, Allen
Bradley PLC5 with battery chip, 230/3/60, rear, 4 KW heater (7 zone) , 15 hp
hydraulics, Dri-Air drier, 1996* (MN) |
|
35 ton |
plastic, injection molder: Autojectors WDHS-35-S, vertical insert
molder, 4.9 ounce shot size, 16" side to side shuttle table, 8" x 10" mold
base, 7-1/2 hp hydraulic pump, variable volume pump control, digital
controls,, electrics, new 1995* (MN) |
|
70 ton |
plastic, injection molder: Autojectors HS-70-S, vertical clamp, 6.9
ounce horizontal shot, 1-3/4"" barrel screw, oversize shuttle table, Siemens
TI-545 PLC & TCAM interface, 8' x 8' x 8'H, 10,000#, 1992* (MN) |
|
88 ton |
plastic,
injection molder: Battenfeld BA800/315 CDC, 25" x 25" platens, 16.5" x
16.5" btb, 7 ounce shot size, 16.73" stroke, 24.61" daylight, Unilog 4000B
controller, core pull, hydraulic knockouts, 1995* (MN) |
|
2.2 lb |
plastic, sprue
picker: Conair-Harmo FX-150, fits 60-150 ton injection molder, 21.7" arm
stroke, 140 degree swing angle, 50 to -90 degree swing angle, controller,
2000* (NJ)(11) |
|
4.4 lb |
plastic, sprue picker: Conair-Harmo FX-250, fits 150-250 ton injection
molder, 25.6" arm stroke, 3.7" - 19.5" strip kick stroke, 4.4# payload w/o
wrist rotation, 2.2# payload w/wrist rotation, 3.8 second minimum cycle
time, 2000* (MN)(3) |
|
8" |
polisher: Buehler Ecomet III grinder/polisher, 50 - 50 rpm, gear drive,
swing-spout water faucet, catalogue no. 49-1650-160, 115/1/60, s/n -
338-ECH-2062* (MN) |
|
15 ton |
press, die cutting:
Preco 1212C, hydraulic,
C frame, 0"-4" stroke,
micrometer adjustment,
12" x 12" bolster,
230/3/60,
Series 104 control, aftermarket
feeder, 2000* (MN) |
|
25 ton |
press, die cutting (clicker): Herman Schwabe D swing-arm die cutter,
hydraulic, 1/2" - 2-1/2" stroke, 9" daylight, 23" x 24" upper platen, 13" x
30" lower bed w/24" x 40" bolster plate, adjustable daylight & stroke
(manual), starter switch, palm buttons, 1980* (MN) |
|
40 ton |
press, die cutting:
Preco 1320-L, 4-post, hydraulic,
13" x 20" cutting area, 2" stroke,
micrometer adjustment, dual drive,
front & rear roll feeds,
SBCIII control, jog/speed/direction,
hydraulic,
light curtains, die
clamps,
electrical
cabinet,
21334 hours,
460/3/60,
1995* (MN)
|
|
30 ton |
press, die cutting:
Samco GTH, model TH-35 2075,
travelling head,
joystick controller,
6" stroke, 1" - 7" daylight,
30" x 30" cutting
platen, 30" x
79" between uprights, 65" ram travel (left/right),
hydraulic, 3.2
hp (230/460/3/60),
64 litres Mobil DTE 26,
460/3/60, 2200 kg,
29-1/2" x 74" platens, pump
motor, 1996* (MN) |
|
30 ton |
press, high speed:
Minster TR2-30 Pulsar SSDC press, 100-1400 strokes per minute, 1" stroke,
11.375" - 13.125" shut height (adjustable), 1.75" motorized adjustment, 30"
x 21" bolster, air clutch, remote console, Vamco feed, auto lubrication,
sound enclosure, 1982* (IL) |
|
60 ton |
press, high speed: Bruderer 50/60
precision, high speed, 4 post, 5/8" - 2" stroke, 100 - 1200 strokes per
minute, 29.92" x 25.59" bolster, 30" x 16.54" ram, 30.3" tool opening, 25 KW
drive, 460/3/60 electrics, BBV 202/120 feed, remote console, 1997 - new
bolster & rebuilt clutch, brake & flywheel, 2000 - motor rebuilt &
hydrostatic drive rebuilt by Bruderer, sound enclosure, excellent
maintenance records, 1981* (MN) |
|
60 ton |
press, high speed:
Bruderer BSTA60II HL precision, 4 post, long bed, 5/8" - 2" stroke, 100 -
1120 strokes per minute, 36.5" x 25.59" bolster, 36.5" x 16.54" ram, 37.2"
tool opening, 8.36" - 11.57" shut height, 25 KW, hydrostatic drive, 460/3/60
electrics, BBV202/120 feed, remote console, 124" x 96" x 136" high, sound
enclosure. 1984* (MN) |
|
4
ton |
press,
hydraulic: Denison
TO45H, 12" stroke, 18" daylight, inching,
palms, C204 full safety
valve, missing anti-repeat board, full cycle,
heater controls, 5
hp, 220/3/60* (MN) |
|
10 ton |
press, hydraulic: Eitel RP-10 straightening press, 5" stroke, 8" x 51"
table, rolling fixture with roller style work supports, lever operated ram,
adjustable ram speed, motor, hydraulic, 230/3/60, 1970* (MN) |
|
18 ton |
press, hydraulic:
Neff D15-5M, 7" stroke, 18" daylight, 9" throat, 12" x 15" bolster, factory
bench, palms, ram speeds: 153/60/98 inches per minute, 9-36 strokes per
minute, 1999* (MN) |
|
75 ton |
press, hydraulic:
K.R. Wilson 37FX, H-frame shop press, s/n - 2705, |
|
10 ton |
press, mechanical:
Whitney Jensen #130, 18" throat, 12" x 18" bed, 1-1/4" stroke, 1-3/4" adj. ,
7" die space, $750.00* (MN) |
|
22 ton |
press,
mechanical: Minster #3 OBI,
4" stroke, 8.75" shut height, 12" x 20" bolster, 115 strokes per minute,
air clutch & brake, 1965* (CA) |
|
35 ton |
press,
mechanical: South Bend/Johnson
35-FW-AC OBI, 2-1/2" stroke,
11" shut height, 100-200 spm,
24" x 15" bolster, CWP roll feed, air clutch, palms, excellent, 1979* (MN) |
|
45 ton |
press, mechanical:
Komatsu OBS 45-3 OBG, 3.94" stroke, 9.84" shut height, 2.36" ram adjustment,
50-100 spm, 31.5" x 17.7" x 4.33" bolster, controls, 15.7" x 13.8"
ram, hydraulic overloads, air clutch & brake, palm buttons, crank angle
detector, solid state controls, isolation pads, 230/3/60, Hitachi AC
inverter, transformer, excellent, 1987* (MN) |
|
60 ton |
press, mechanical:
Rousselle #6A OBI, 3" stroke, 12-1/2" sh, 50 spm, air clutch & brake, air
cush, palms, 1981* (IL) |
|
10 ton |
press, straightening: Eitel RP-10 straightening press, 5" stroke, 8" x
51" table, rolling fixture with roller style work supports, lever operated
ram, adjustable ram speed, motor, hydraulic, 230/3/60, 1970* (MN) |
|
200 ton |
press, mechanical: Niagara SC2-200-7242, straight side, double crank,
12" stroke, 32" shut height, 72" x 42" bolster, 30 strokes per minute, 21" x
20" windows, (2) air cushions, air clutch & brake, clean & quiet, 1973* (IN) |
|
50 ton |
punch,
fabricating: Whitney 652-50, 30" throat, 30" x 72" working surface,
duplicator, 20 hp hydraulic drive, air over hydraulic punch clamp, quantity
of tooling, 1973* (MN) |
|
15 ton |
punch, turret:
Rotex 18C, 18 station, 18' throat, 2-1/4" punch capacity, factory stand,
1970* (MN) |
|
15 ton |
punch, turret:
Rotex 18C-2.25, 26" throat,
18 station, 2-1/4"
largest punch,
full set of punches,
many punches unused,
more punches,
factory stand, work light, 825# weight, will punch center of 52" sheet,
s/n - 32939, 1988* (MN) |
|
riveter: VSI
Automation TM6 Spinomatic, rotary table, temporary specifications, s/n -
23583* (MN) |
|
.25" |
riveter:
Baltec RN-180, 3/4 hp, timer,
controller* (MN) |
|
.50" |
riveter:
Baltec RN-280, timer, controller, 1 hp, 460/3/60, temporary specifications*
(MN) |
|
.125" |
riveter:
National 2400B, dual head, 8" throat, 0"-8" adjustable centers, 1/2 hp*
(MN)(2) |
|
.186" |
riveter:
National 1600F,
pnuematic, 14" throat,
offset for hard to reach
spots, rotary hopper, 50 cycles/minute, .085" x 1/8" minimum rivet,
.186" x 3/4" max rivet, 3" stroke,
tooled for
7/16" & 9/16"
rivets with
.334" body,
Protectomatic & Touchomatic
safety controls, foot pedal,
825# weight. 1993* (MN)(3) |
|
.25" |
riveter: VSI
Automation TM10 Spinnomatic, .02" minimum, 6-station rotary table, .5 to 15
second cycle time, 3/4 hp, 1974, 208/220/440/3/60, rear view, currently
wired 440 volt, controls* (MN) |
| 14 gauge |
rollformer: Lockformer 14 gauge Pittsburgh Lock, 7 forming stations,
auxilliary 3 in 1 combination rolls, 1999* (MN) |
|
16 gauge |
roll former:
Flagler "heavy duty" Pittsburgh
machine, 7 stand,
Pittsburgh
& drive cleat rolls, 30 feet per minute,
2 hp, 208/220/440/3/60,
being painted* (MN) |
| 20
gauge |
rollformer: Engel 835, 8-station, 1.5" shafts, 5" between rolls, 3"
vertical roll height, 2 sets of interior rolls, government lock rolls are
standard, 5 hp, 198x (MN) |
| 20
gauge |
rollformer: Lockformer 8900 Cleatformer, 9-station, 100 fpm, temporary
specifications, 1969* (MN) |
| 3"x3"x3/8" |
rolls, angle: SMT Pullmax Z31, horizontal/vertical, 3 roll drive,
9-13/16" diameter rolls, 26 fpm, 36" minimum leg out diameter, 2-1/2" x
2-1/2" x 3/8" leg in - 48" minimum diameter, 6.6 hp rotation motor, 2.4 hp
hydraulic pump motor, guide rolls (manual adjustment)* MN* |
| 12
gauge |
rolls, plate: Niagara #351, 4' x 12 gauge capacity, manual, drop end*
(MN) |
| 10
gauge |
rolls, plate: Hendley & Whittemore 3F, 7' x 10 gauge capacity, initial
pinch, angle rolling attachment* (MN) |
|
25" |
sander, belt: Ramco 25T75, single, vertical head , 24" x 75" belt, 10 hp
main motor, 20-80 fpm, 1 hp feed motor, belt cleaning brush, (2) AAF dust
collectors & filter, good contact rolls, 1987, 230/3/60* (MN) |
|
15" |
sander, disc:
State, 1 hp, 220/440/3/60,
22" x 9" tilting table,
start/stop switch* (MN) |
|
9" x 11" |
saw,
band, horizontal: DoAll C-4, 1" blade, spring loaded head, 1965* (MN) |
|
10" x 12" |
saw,
band, horizontal: DoAll C-260A-2, 1-1/4" blade, 0"-24" auto feed
w/multiple indexing, 20-350 fmp blade speed, bundling attachment, 1991* (MN) |
|
12" x 12" |
saw,
band, horizontal: DoAll C-305A, 1-1/4" blade, 0"-16" auto feed
w/multiple indexing, 20-350 fpm, 5 hp, 1997* (MN) |
| 18"
x 22" |
saw, band,
vertical: Marvel 8/M8, 45 degree manual tilt frame, 18" x 22-1/2"
maximum capacity, 18" x 14" capacity @ 45 degrees, 3/4" blade, 1.3 hp
motor, 3 speed ranges, 20-200 FPM, vise, 575/3/60, 1978* (MN) |
|
30" |
saw,
band, vertical: DoAll 30-M,
has blade guard for 16" throat using 2 wheels, 64" x 44" x 75"
high (on skid), blade welder/grinder,
1959* (MN) |
|
36" |
saw, band,
vertical: DoAll 36R Zephyr, 20" under blade guides, lower 10 hp drive
motor, 0 - 10,000 fpm blade speeds, cover open, 1957, rear view, extra drive
belts* (MN) |
|
36" |
saw, band, vertical:
Doall ZW-3620, 20" under blade guides,
0-15,000 fpm blade speeds,
15 hp, tilt
table, tension
indicator, extra
blades,
heavy
duty blade
guides, exc condition, new
1960* (MN) |
|
36" |
saw, vertical:
Grob 6V-36, 25-15,000 fpm blade speeds, 36" x 36" tilting table, 20" work
height, air/hydraulic table feed, blade welder & grinder, 15 hp brakemotor,
230/460/3/60, 1991* (MN) |
|
50" |
scrubber & sweeper: Advance 5015 Hydro-Cat, riding type, 50" scrubbing
width, (4) 13" scrub brushes, sweeping brush, 66" turning radius, 4 cylinder
engine, propane, 0-8 mph, 60 gallon solution tank, 50 gallon recovery tank,
84,000 square feet/hour, 352 hours use, , 1996* (MN) |
| 16
gauge |
shear, power: Wysong, model H-52, hydraulic, 16 gauge, front supports,
foot pedal control, covers, s/n - H32470, quiet pump* (MN) |
|
52" |
shear, power: Famco, model 1252, mechanical, inch/single/continuous, 12
gauge, front supports, foot actuator, 5 hp, 230/460/3/60, 1975* (MN) |
|
10 gauge |
shear, power: Pexto 10-U-6A, mechanical, 6' squaring arm, front
supports, 1970* (MN) |
|
10 gauge |
shear, power: Pexto 10-U-6B, mechanical, 6' squaring arm, supports, 24"
rear operated back gauge, 1970* (MN) |
|
10 gauge |
shear, power: Pexto 10-U-8, mechanical, 6' sauaring arm, 24" front
operated back gauge, extra blades, 1960* (IL) |
|
spin welder:
Vercon Autoweld AW-1, up to 8" part height, up to 6" diameter,
friction welds halves of plastic
parts, adjustable upper jaw,
fixed lower jaw, 1-1/2
hp variable speed drive,
230/460/3/60 electrics,
7 station timer, 48" x 48" x 100" high* (MN) |
|
22" |
slitter:
Dahlstrom with rewinder,
2-1/4" shaft diameter, with tooling, 19xx* (MN) |
|
.188" - 3" |
swager:
Sierracin Harrison
8777-7
"torque plus" (internal & external)
roller swager,
dual head
(small:
.188" - 1.250"/large:
1.250" - 3"), 3-groove, automatic, calibration kit, makes
aircraft high pressure (5000 psi) hydraulic fittings with titanium,
electronics, torque or diameter control, touch screen,
Sierracin tooling for Boeing 7D0028 unions & 7D0030
sleeves, 480/3/60, 2000* (MN) |
|
45 KVA |
transformer: Square D 45T6H, three phase, 480 volt primary, 240 volt
secondary, rainshield* (MN) |
|
39,500# |
truck, platform lift: GMC 7000 medium duty, 7'4" x 14' scissors-lift
bed, 17,975 miles, 1985* (MN) |
| 1-1/2" |
tube bender:
Diacro 8, hydraulic, 1" solid, 1-1/2" tube (16 ga wall), 24" maximum radius,
3500# torque with 4" cylinder, 3 hp, 208-220/3/60, 1150# weight, Control-A-Bend, s/n - 1-1071* (MN) |
|
tube
bending dies: (18) Pines pin type rotary draw dies, inserted die (bolt
on clamp), left hand only* (MN) |
|
3" |
tube endformer: Eagle
Precision I/O,
horizontal,
single ram,
dual (inner/outer)
hydraulic cylinder, manual
adjustment, AEG Modicon
M984 PLC, shuttle table,
10 hp pump, 480/3/60,
control,
water cooled, uses serrated tooling (automatic lubrication), s/n
- 2658* (MN) |
|
1-3/4" - 3" |
tube endformer tooling: Eagle Precision I/O, inner segmented
expanding fingers & outer reducing jaws,
lubricated barrel,
back plate, separator plate,
mandrels, lifting
handle, 67 assemblies,
extra & (61) incomplete* (MN) |
|
20 kHz |
ultrasonic booster: Branson 900 series, gold aluminum, 1.5:1 gain,
excellent condition* (MN) |
|
20 kHz |
ultrasonic booster: Branson 900 series, purple aluminum, fair condition*
(MN) |
| 1000 watt |
ultrasonic converter: Branson 902JA, 20 kHz, fair condition, s/n -
NQ50328A* (MN) |
| |
ultrasonic converter:
Branson 902J, elongated
lug holes, s/n -
NQ50328A |
| 2000 watt |
ultrasonic converter: Branson 922JA, excellent condition* (MN) |
|
ultrasonic welder: Hermann, actuator, converter, booster, Dialog 2012
power supply, palms, manual* (MN) |
|
350 watt |
ultrasonic welder: Branson 943M power supplies, 40 kHz, RF & control
cables, 220/1/60* (MN)(7) |
|
650 watt |
ultrasonic welder: Sonobond Sure Weld 635, 35 kHz plastic welder, press
with palm buttons, UGE35-6 control, RL power supply, manuals & tooling* (MN) |
|
700 watt |
ultrasonic welder: Branson 941AES intelligent actuator (5), Branson 947M
power supply - needs repair (1), 40 kHz, RF cables, converters & boosters,
Branson columns, 1991-1997* (MN)(5) |
|
700 watt |
ultrasonic welder:
Branson 947M Advanced power supply, 40 kHz, pricing, cover removed* (MN)
|
|
900 watt |
ultrasonic welder:
Branson 184P power supplies (2), 801 actuator (1), RF cables, 2000 kHz* (MN)
|
|
900 watt |
ultrasonic welder: Sonobond 351 press/actuator, PCSIIGM35-900
microprocessor power supply, MW935 35 kHz metal welder* (MN) |
| 1000 watt |
ultrasonic welder: Branson 901 AES actuator with base & palms, 910M
power supply with RF cables, 902J converter, booster, EC-1 communications
port, tools, excellent* (MN) |
| 1000
watt |
ultrasonic welder: Branson 910IW, 20 kHz, silver booster, 902J converter,
1994* (MN) |
| 1000
watt |
ultrasonic welder: Branson 910IW+, 20 kHz, gold booster, 902J converter,
1998* (MN) |
| 1000 watt |
ultrasonic welder: Branson 900AE actuator, 1995-1996 (2), Branson
910M power supply, 20 kHz, some RF cables, converters & boosters, Branson
columns, 1991-1995* (MN)(6) |
| 1000 watt |
ultrasonic welder: Branson 910IW, 20 kHz, 902J converter & booster,
inside electrics, 1995* (MN) |
|
ultrasonic welder: Dukane 43A250 w/Ultracomm, temporary specifications*
(MN) |
| 1000 watt |
ultrasonic welder:
Dukane 43A255 actuator, 20T1000 power supply, 110-3122 converter (2)* (MN) |
|
2000 watt |
ultrasonic welder:
Branson 920IW+,
20 kHz, weld
by distance, base
with palm buttons, converter, gold booster,
very very
clean, control
keypad,
control
lit,
stack
test,
air controls,
1996*
(MN) |
| 2000 watt |
ultrasonic welder: Branson 920IW+, 20 kHz, 922JA converter, gold
booster, very clean, from original owner, 1996* (MN) |
| 2000 watt |
ultrasonic welder: Branson 921AES intelligent actuator & column, no
base, RF cables, converter, booster* (3), 920MA Advanced power supply,
1995-1997* (3)(MN) |
| 2000
watt |
ultrasonic welder: Dukane 43A255, 20 kHz, 20A2000
power supply, finger touch controls* (MN) |
| 2000 watt |
ultrasonic welder:
Dukane 43A255 Ultra Heavy-Duty press/thruster, no power supply, 20 kHz,
1995* (MN)
|
28r>
2000 watt |
ultrasonic welder:
Dukane 43A255 Ultra Heavy-Duty press/thruster, rf cables, 7" stroke, 1997*
(MN)
|
| 2000
watt |
ultrasonic welder: Branson 920IW, 20 kHz, 922JA converter, gold booster*
(MN) |
| 2000
watt |
ultrasonic welder: Branson 920IW, 20 kHz, 922JA converter, silver
booster, 1996* (MN)(3) |
| 2000
watt |
ultrasonic welder: Dukane 43E255 actuator, 20T2000 power supply, RF
cables* (MN)(4) |
| 3000 watt |
ultrasonic welder: Stapla Condor ST30,
ST3000 digital generator (power supply),
converter, RF
cables, palm buttons, system
one, system
two, system three, 2000* (MN) |
|
900# |
vibration tester:
Ling 1512 shaker,
12" table, 900# sine
force, 750# random force, Ling
712939-120 5R-S control
w/CRT, Ling DMA2/1512-2
amplifier, 15
KVA input, 13 KVA output, power & control cables, shaker
s/n - 30* (MN) |
|
900# |
vibration tester: Ling Dynamic Systems V722 shaker, 900# sine/750#
random force, 1" stroke, 9.5# armature, air cooled, 3.11 KVA amp, DVC4000S
control, 1997* (MN) |
|
6000# |
vibration tester:
Unholtz-Dickie T-513 electrodynamic shaker, 6000# sine force/3000# random
force, unitized base with 24" x 24" slip table, 1" stroke, 12" diameter
table, 36# armature, TA117-60 solid state amplifier (water cooled) ,
Schlumberger 1210 random vibration controller, Hauck TBA-20-10-5 blower,
power cords, power cords, 198x* (MN) |
|
8,000# |
vibration tester: Unholtz-Dickie T1000 electrodynamic shaker (air
cooled), 1" stroke, 16" diameter table, 90# armature, 310# maximum sine
payload, TA-116-80 solid state amp (water cooled), 480/3/60, 65 KVA, SP7
manual servo controller, OSC-1S sweep sine generator, trunnion base, 8000#
sine force, 4000# random force, blower, recently arrived, rebuilt mid
1990's, new 1976 |
|
30,000# |
vibration tester: Ling #249 electro-dynamic shaker, 30,000# sine/24,000#
random force, 1" stroke, 28" table, water cooled, 28,800# weight, 197x* (CA) |
|
vibration welder: Branson CV12 orbital, 18" x 18" platen, 37" clearance,
12" drive platen, 13"-19" opening, 0-700# clamp force, light curtains, opto
touch sensors, 1995* (MN) |
|
LV-38 |
vibration welder:
Vinton
linear, 19-1/2" x 38" lift table, hydronamic drive head, missing
PLC, I/O;s and Moog valve, has Panelview 1000, 480/3/60, rebuilt, s/n
- NA-VB107* (MN) |
|
LVW-4822 |
vibration welder:
Bielomatik linear,
electro-mechanical,
30 KW Lenze
digital
vibration drive, 180-240 Hz resonant frequency with
auto
search), 0.2-1.55 mm amplitude, 60 kg maximum tool weight,
54" x
22" clamp area (lift table),
33-1/2" x 19-3/4" vibration clamp
area, 15-30 second cycle time, Allen
Bradley SLC5/04,
Allen Bradley
Panelview
1000, weld by distance, 35 KW load, 480/3/60,
sound enclosure, access lift gate,
finger actuator, installed
2004,
2002*(MN) |
|
LVW-4822 |
vibration welder:
Bielomatik
linear, 47" x 20" max part size, 30 KW
Lenze
digital vibration drive, 180-240 Hz resonant frequency, 0.2-1.55
mm amplitude, 60 kg maximum tool weight,
54" x
22" clamp area (lift table),
33-1/2" x 19-3/4"
clamp vibration clamp,
15-30 second cycle time, Allen Bradley SLC5/04 PLC,
Allen Bradley
Panelview
550 interface, weld by distance,
electrical
cabinet, software backups
& manuals,
32 KW load, 480/3/60,
2005*
(MN) |
|
LVW-7SA |
vibration welder:
Vinton linear, 20" x
36" lift table,
hydronamic
drive head,
Moog valve,
rebuilt in
2/2001 schematics, missing
Allen Bradley plc control,
old control legend,
Panelview
1000 interface,
software
backup, light curtain, OptoTouch*
(MN) (VB103-Grand Prix, s/n - 40665) |
|
Mini II |
vibration welder:
Branson
linear, 11 KW,
.040" - .070" amplitude,
240 Hz, meltdown, tool
slide, part eject, 5 second cycle,
AB SLC500 & Panelview, palm buttons, 480/3/60, rear, 1999* (NY) |
|
VBW-3700 |
vibration welder: Dukane linear,
AB 1336 Plus II
30 hp
digital vibration drive,
24"
x 52" tool size (90#-150# weight) & lift table (11.5" x 38"
opening), 20"
table stroke (3.6
hp
hydraulic), 25"
daylight, light curtain,
weld by distance,
finger actuators, Allen Bradley
SLC5/03 PLC
& AB 600
color
touch screen,
setup mode, set
load position, auto tuning,
4-rail
table slide system, 480/3/60.
600/400/3/60 transformer, 7000#,
457
production hours, new
2006* (MN) |
|
VW-4 |
vibration welder: Branson VW90-4,
linear,
21" x 34" lift table w/12"
x 16" slot, electro-mechanical drive,
Emerson Prism 5 hp DC drive, 240 Hz,
weld by
distance, motorized
table elevation, Allen Bradley
Slick
500 (SLC500) plc &
DTAM
interface, light curtain,
electrical cabinet, Optotouch, right hand
control, 460/3/60
w/transformer*(MN) |
|
VW-4 |
vibration welder: Branson VW90-4, linear, 21" x 34" lift table w/12"
x 16" slot,
electro-mechanical drive, Emerson 7-1/2 hp, 240 Hz, weld
by distance, motorized table elevation, Allen Bradley Slick 500 (SLC500) plc
& DTAM interface, light curtain, electrical cabinet, Optotouch, rear
view, 460/3/60 with transformer, left hand control, under power* (MN) |
|
VW-4 |
vibration welder: Branson VW90-4, linear,
21" x 34" lift table
w/12" x 16" slot, electro-mechanical drive, Emerson Prism 5 hp DC
drive, 240 Hz, motorized table elevation, Allen Bradley Slick 500 (SLC500)
plc & DTAM interface, light curtain, electrical cabinet, Optotouch,
right hand control, 460/3/60 w/transformer, 6-1/2' x 3-1/2' x 8-1/2'H*(MN) |
|
VW-4 |
vibration welder: Vinton LVW-4S linear vibration welder, hydronamic
drive head, Moog 760Y913-534 valve (Hydraulic amplifier) , 40" x 20" lift
table (hydraulic) , digital weld control, process control, weld height, weld
time (with meltdown), light curtain, part eject/knockouts, hydraulic pump,
palm buttons, cycle counter, electrics, GE controller, 1992* |
|
VW-4L |
vibration welder:
Branson linear,
17
hp Vectron DC drive,
18" x 33.5" maxiumum part size, 18" x 30" drive platen
(12" x 15" opening),
35#
drive fixture (50# maximum),
21 x 33.5" lift table, (11.5" x
23.5" opening), 20" variable (hydraulic) stroke,
weld by distance,
pnuematic table clamping, light
curtains, palm buttons, Allen Bradley
SLC5/05 PLC, (powered), Allen Bradley
Panelview
550 touch screen interface,
480/3/60, 5 second dry cycle time,
2001* (MN) |
|
VW-6 |
vibration welder:
Branson 90 series, linear model 9610
45" x 25-1/2" lift table, electro- mechanical
drive head,
Emerson Laser 7-1/2 hp
drive, 240 Hz frequency, table elevation
motor, 1992* (MN) |
|
VW-6 |
vibration welder:
Branson linear, VW90-6,
21-1/2" x 46"
lift table w/11-1/2"
x 32" slot, 20" stroke,
weld by distance,
electro-mechanical
drive head,
Commander 10 hp digital vibrator drive (lit
up),
180-240 Hz (variable), Allen
Bradley SLC500
plc, DTAM
interface, 460/3/60,
load
sentinel, light curtains,
controls lit up,
34 KVA transformer, part
hold downs, 7' x 3-1/2' x 8'5" H,
new 1992* (MN) |
|
VW-6 |
vibration welder: Branson 96DVW6, linear vibration welder, 45" x 25.5"
lift table, 22" stroke, electro-mechanical head, Commander CDE 15 hp
drive, 240 Hz frequency, .040"- .070" variable amplitude, motorized table
elevation, 480/3/60, Allen-Bradley Panelview 1200 control,
manual/automatic/tooling setup, SLC 5/04 CPU, light curtains, 1996* (MN) |
|
VW-6UH |
vibration welder:
Branson Ultra Hy-Line, linear,
15 hp Commander digital vibration drive, 20" x 48" part size, 80# top tool weight, 22" x 46"
lift table, 20" table stroke (hydraulic)
11.5" x 38" central opening,
weld by
distance, Allen Bradley
SLC5/04 PLC,
statistical process control,
light curtain, finger actuators,
rear access
doors, 480/3/60,
Xycom color touch screen,
setup screen,,,
self tune screen,
system parameters screen,
parameter configuration screen,
1998* (MN) |
|
6 cu ft |
vibratory finisher: Harper Electro Deburring EDV-6
tub type, 40" x 12" x 16" deep, urethane lined, timer, discharge, 3 hp,
variable speed, liner like new, forward/reverse switch, 1981* (MN) |
|
30" dia. |
washer, parts: Landa SJ-150 front loading, 14-1/2" above lower 30"
basket & 17-1/2" above upper 30" basket, oil skimmer, 104 gallon tank, 180F
temperature, 5 hp pump, 10/100 gpm, timers, 1998 (MN) |
|
40" |
washer, parts:
Better Engineering F-4000-LXPZX
"Purifier" Jet Washer, (2)
40" diameter baskets (1500# lower/200# upper),
60" work height, 26-1/2" bottom basket height, 27-1/2" top basket
height, front
loading, uses
130F-180F water & detergent,
10 hp pump,
timer, ARC-11 rinse system,
oil skimmer, 1997,
interior repainted with enamel* (MN) |
|
300 amp |
welder, mig: Hobart RC-301 power supply, 2000 wire feeder, temporary
specs* (MN) |
|
.040" |
wire forming:
U.S. Baird 00
fourslide, 7/16" strip width,
4-1/4" feed, 100-500 spm,
straightener, Durant counter,
speed control, missing
forming slides, 2000* (MN) (2) |
| 32-8 AWG |
wire stripper: Eubanks 2900, strips 1" & up lengths, electrics,
inch/metric, prefeeder, counter, tag* (MN) |
|
8" |
woodworking,
jointer: Northfield 8-LD, 10" x 73" table, 3 hp, 230/460/3/60, 1965*
(MN) |
|
8" |
woodworking,
jointer: Northfield 8-MD, 10" x 76" table, 3 hp, 230/460/3/60, rear
view, 1989* (MN) |
|
2" x 6" |
woodworking, moulder: Stetson-Ross XL, model 628,
four sided, 15 hp cutterhead, 8000 rpm spindle, 5 hp cutterhead, 1-1/2 hp
variable speed feed (20-70 fpm), belt drive, 1978* (MN) |
|
|
|
|
|
/TABLE>
